copy and paste this google map to your website or blog!
Press copy button and paste into your blog or website.
(Please switch to 'HTML' mode when posting into your blog. Examples: WordPress Example, Blogger Example)
Input Form:Deal with this potential dealer,buyer,seller,supplier,manufacturer,exporter,importer
(Any information to deal,buy, sell, quote for products or service)
Seal compatibility in hydraulic systems - ExxonMobil such as DIN 51524, ISO 11158 and ASTM D6158 Decreasing hardness of seal in test Change in hardness (Shore A hardness) Mobil DTE 24-8 00-7 00-6 00-5 00-4 00-3 00-2 00-1 00 0 00 Conventional Hydraulic Oil Seal Compatibility 168 hrs, 100°C, NBR -1, Shore A Hardness Run under DIN conditions Increased seal swell % Volume change (seal swell) Mobil
Chemical Compatibility | Rubber | Elastomer - Hi-Tech Seals Inc. Elastomer may exhibit slight swelling and or loss of physical properties under severe conditions: Fair Possible loss of physical properties 10 - 20% If you would like more information on chemical compatibilities please contact a Hi-Tech Seals sales associate directly Hi-Tech Seals Inc assumes no responsibility whatsoever for use of this
Chemical Compatibility - Totally Seals It's imperative that you understand the properties of each seal material and their chemical compatibility if you are attempting to use a polymer in a critical environment Use this guide as a reference by selecting the chemical or sealing material you wish to use Nitrile O-Rings Nitrile O-Rings 1mm Cross-section 1 5mm Cross-section 2mm
O-Ring Chemical Compatibility Guide - Marco Rubber FAM TEST FUELS DIN 51 6040A; FAM TEST FUELS DIN 51 6040C; FATTY ACIDS; FATTY ALCOHOL; FC 11 (Trichlorofluoromethane) FC 112 (1,20Difluorotetrachloroethane) FC 113 (1,1,20Trichloro01,2,20trifluoroethane) FC 113 AND HIGH LOW ANILINE OIL; FC 114 (1,20Dichlorotetrafluoroethane) FC 114B2 (Dibromotetrafluoroethane) FC 115 (Chloropentafluoroethane)
Chemical Compatibility | Rubber | Elastomer - Hi-Tech Seals Inc. Elastomer may exhibit slight swelling and or loss of physical properties under severe conditions: Fair 12% and Freon 12, 80%: Unsatisfactory Hydraulic Oils DIN 51524: Satisfactory Hydraulic Fluids, Oil-in-Water Emulsions HFA
Seal compatibility in hydraulic systems - eberhart. ch as DIN 51524, ISO 11158 and ASTM D6158 Seal compatibility in hydraulic systems a standard seal test using Nitrile NBR-1, the most common elastomer used in hydraulic systems, ISO VG 46 oil are between 0 to 12% Mobil DTE 20 is designed to provide extra seal swell properties as demonstrated by the results of this test This higher swell
Chemical Resistance Chart - Elastomers | Phelps Industrial Products Chemical Resistance Chart - Elastomers, Phelps is a major manufacturer, fabricator and distributor of Industrial Gaskets, Compression Packing and Sealing Devices Established in 1945 to deliver the best performing fluid sealing products at competitive prices globally
Technical Handbook O-rings 5. Designing with Rubber steady and no motion or force causes a break in the line of seal contact Also, swelling caused by contact with the service fluid, may compensate for compression 395 and DIN 53517 ISO 815 Table 3A-1a gives compression set values for standard Eriks compounds, (Squeeze 25%) Compression set 22h 100°C (212°F) 14,8 12,8 9,2 Compression
Ultimate Chemical Compatibility Chart - Rhondama Seals Hydraulic Pneumatic Seals Bonded Seals Bearings NBR = Nitrile-butadiene-Rubber HNBR = Hydrogenated Nitrile 1 = Good < 15% swell Materials 4 = Not recommended FKM = Viton® (Type A) EPDM = Ethylene Propylene 2 = Fair 15% - 25% swell X = Not Tested FVMQ = Fluorosilicone