copy and paste this google map to your website or blog!
Press copy button and paste into your blog or website.
(Please switch to 'HTML' mode when posting into your blog. Examples: WordPress Example, Blogger Example)
Input Form:Deal with this potential dealer,buyer,seller,supplier,manufacturer,exporter,importer
(Any information to deal,buy, sell, quote for products or service)
www. ka-t. org - Index page KA-T ORG FORUM ANNOUNCEMENTS AND NEWS Check in here to find out about important news and events on the ka-t org forums
KA-T. org - The Home of 1000+ whp 7 sec Turbo KAs Welcome to KA-T org - the Home of 1000+ whp 7 sec Turbo KA's You will find a wide variety of KA-T resources all throughout the site, including featured rides, tech articles, timeslips, dyno sheets, photos videos, product comparisions, etc Please join the forums and get connected with almost 11,000 members that are constantly trying to push the envelope of the KA within the market Tech Tips
Ka24det headgasket options - www. ka-t. org I currently have a ka24det with a felpro headgasket on a sr20det t25 running 10psi of boost; decently quick I'm about to build another ka24det and was wondering how much boost power is the felpro paper type headgasket good for (apparently I heard 400) I know people always bash on felpros and I was planning to run a multiple layer steel type cometic HG, but I also hear bad stuff about them I
is the crank supposed to be hard to spin after installing? Hey guys, im just putting toghther my bottom end finally today and i plastigauged the main bearings, they are 0 001 at most So their kinda tight I went ahead and lubed the bearings with the arp lube that came for the studs and then followed the arp torque procedure from JGS to torque them all down Now the problem with that is, at the 25ft-lb mark i can barely turn the crank by hand at
new kat dyno z31 turbo 8psi - www. ka-t. org Re: new kat dyno z31 turbo 8psi by AtomGrimus » Sun Feb 08, 2015 5:41 am im like 2 years late here lol, i got a t3 z31 turbo, i did research and it says on other forums that this turbo can only hold up to 6psi idk how true that is
swirl control valve - what exactly does it do? - www. ka-t. org The operation of the swirl control valve extends the torque curve of the engine It does this by essentially providing two seperate intake velocities and torque curves that are switched, overlaying the curves as a single extended profile The SCV are operated by a proprietary load and rpm based switching algorithm The ka24e ecu uses seperate maps for each "state" of the SCV (open or closed
Intercooler sizing - www. ka-t. org by ppctx » Fri Jun 06, 2008 12:02 am come on gentlemen, this is a kat forum somebody has to have a little expertise with this topic
HowTo: S14 Walbro fuel pump install - www. ka-t. org 95 s14 kaT t3 t04e (60 trim), bikirom, groundzero mani dp, 82 lb AMS FS 94 d21 kaE 4x4 stock BillKlineVT Dont Question My Nissan Knowledge Posts: 786 Joined: Thu Oct 14, 2004 5:06 am Location: Blacksburg, VA and Barre, VT
Question: SR20DET ECU on KA24DE? - www. ka-t. org i have a bikirom but for the longest time i've wanted COP I definately like this idea How expensive are sr20 ecu's? i guess it could be difficult to get a cas wheel though Marko 95 s14 kaT t3 t04e (60 trim), bikirom, groundzero mani dp, 82 lb AMS FS 94 d21 kaE 4x4 stock rex2sx NooB Posts: 2 Joined: Fri Apr 24, 2009 5:59 pm Location: Mohnton, PA