copy and paste this google map to your website or blog!
Press copy button and paste into your blog or website.
(Please switch to 'HTML' mode when posting into your blog. Examples: WordPress Example, Blogger Example)
Input Form:Deal with this potential dealer,buyer,seller,supplier,manufacturer,exporter,importer
(Any information to deal,buy, sell, quote for products or service)
MultiTech Developer Resources Multitech net focuses on collaborative software development for MultiTech products This is an open environment where you can ask development related questions and hear back from MultiTech engineering or a member of this community Select a product or software section for development information or use the forums to directly interact with the community
MultiTech Developer Resources » Downloads 1 Create a support case with the relevant information at https: support multitech com including: a Select Other in the Service Requested drop-down b Select the closest MTCDT or MTCDTIP model to what you have in the Product drop-down (must be a model that ends in 247L or 267L) c In the Subject field, enter Request for Redpine Drivers d
MultiTech Developer Resources » Flashing mLinux Firmware NOTE: This section describes upgrading mLinux™ locally on your device and is intended for experts with the appropriate technical knowledge (Otherwise, use the alternative method Upgrading mLInux ) Refer to the Downloads page for applicable pre-built images The following procedure generally only applies to the MTCDT-xx-210L model but can be used to convert a MTCDT-xx-210A model to MTCDT-xx
MultiTech Developer Resources » Getting Started with mLinux 1 Install and Connect Hardware For Conduit ® installation, refer to the appropriate model and guides through the Conduit product page For Conduit ® Access Point installation, refer to the appropriate model and guides through the Conduit AP product page For Conduit ® IP67 Base Station, refer to the installation guide available through the Conduit IP67 Base Station page 2 Access the
MultiTech Developer Resources » FaxFinder The FaxFinder ® fax server is a turnkey solution that connects to an analog port (s) of a PBX capable of DID to DTMF conversion The FaxFinder-IP provides faxing through an IP telephone system FaxFinder converts faxes to PDF or TIFF files so you can send faxes from any application that can print and receive faxes as e-mails, wherever you are The solution provides distributed faxing
MultiTech Developer Resources » mDot The MultiTech mDot mbed platform page has links to the LoRa API (libmDot) For a sample program showing how to configure and use the LoRa API, go to mDot LoRa Connect Example To flash custom firmware into the mDot, see the relevant steps in Flashing mDot Firmware Guides mDot Quick Start (with MTUDK2-ST-MDOT Developer Board)
MultiTech Developer Resources » MTAC-LoRa Cards The MTAC-LoRa accessory cards enable long range connectivity to distributed assets and sensors using an RF spread spectrum technology by Semtech ® MTAC-LoRa cards also have extended life due to a low power draw The MTAC-LoRa-H and MTAC-LoRa-F accessory cards feature: ISM band scanning and asset management range with LoRa of up to 10 miles 15 km line of sight or 1-3 miles 2 km through
Topic: Factory reset Conduit MTCDT - MultiTech Hi, The process for factory default is the following: —- For Factory Default of Conduit (MTCDT), Conduit IP67 (MTCDTIP), Conduit AP (MTCAP), rCell (MTR), or OCG (MTCDP or MT100EOCG): 1 Power on device 2 Wait for ST or STATUS LED to start flashing with a heartbeat rhythm 3 Press in and hold in the RST or RESET button for over 30 seconds 4 Release the RST or RESET button 5 Wait for device
MultiTech Developer Resources » LoRa Network Server The network server is the center of a LoRa network, it provides communication between motes and applications It ensures message integrity through CRC, CMAC and sequence number tracking AES-128 encryption is enabled through the use of pre-shared keys